[Q25-Q42] Cisco 300-110 Practice Verified Answers – Pass Your Exams For Sure! [2026]

NEW QUESTION 25
A network engineer is deploying Cisco 9130I APs on multiple Cisco Catalyst 9800-80 WLCs with Cisco Catalyst Center. The engineer must enable Cisco AI Analytics and location analytics to use the RRM features to automatically manage the WLC RF profiles. Which type of license must be used on Cisco Catalyst Center?

NEW QUESTION 26
A small customer has a legacy autonomous mode Wi-Fi deployment that provides a low-density and low- capacity service. The customer wants to update and replace this deployment with the latest Wi-Fi technology but has a fixed budget that will pay only to replace the APs. Which architectural controller deployment model suits this requirement?

NEW QUESTION 27
A customer requires the wireless network to perform real-time analysis to reduce congestion, link usage, and infrastructure upgrades. Which Cisco technology can accomplish this analysis?

NEW QUESTION 28
A network engineer is designing a new wireless network for a campus. The network must include optimized performance, avoid interference, availability in high-density areas, and roaming. Which two approaches must be taken? (Choose two.)

NEW QUESTION 29
A customer purchases this Cisco equipment for a new branch office: * 20 Cisco Catalyst 9120 APs * five Catalyst 9130 APs * a single Catalyst 9300 Series Switch The customer wants to extend its existing wired and wireless fabric-enabled network to the branch office and manage all devices via a centrally deployed Cisco Catalyst Center (formerly DNA Center). Which Cisco Catalyst Center licenses are required for the branch office equipment?

NEW QUESTION 30
An engineer must perform a predictive design for a wireless network. The customer has devices that can tolerate at most 100 ms of delay when roaming. Which design criteria must be used?

NEW QUESTION 31
An engineer is performing an AP-on-a-stick survey and finds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements. Which two actions during the survey reduce channel overlap? (Choose two.)

NEW QUESTION 32
During a site survey for a new wireless deployment in a multifloor office building, an engineer must identify sources of interference and ensure optimal AP placement for 5 GHz coverage. While walking the site with a spectrum analyzer, the engineer notices periodic spikes in the noise floor on several channels and inconsistent signal strengths reported by the survey tool, despite visually unobstructed paths. Which action must the engineer take next to accurately assess and mitigate the Layer 1 interference?

NEW QUESTION 33
A school deploys a Cisco wireless infrastructure in its classrooms to support a high density of mobile devices.
The network administrator wants to bond channels in groups of two and only allow APs to send 802.11 management frames at 24 Mbps. What should be included in the design to accomplish this objective?

NEW QUESTION 34
A network engineer is designing a new wireless network for a campus. The network must include optimized performance, avoid interference, availability in high-density areas, and roaming. Which two approaches must be taken? (Choose two.)

NEW QUESTION 35
An engineer is performing capacity planning for an open-plan office with 900 concurrent devices, each requiring 2 Mbps of application throughput. Assuming approximately 120 Mbps of usable aggregate throughput per 5 GHz radio, how should the AP count be determined?

NEW QUESTION 36
Which strategies must the engineer use for the antenna deployment model in a warehouse?

NEW QUESTION 37
An engineer must perform a predictive wireless survey to indicate the number of access points required. The engineer has created a new project and imported the floor plan. Which step must be taken next for accurate AP placement?

NEW QUESTION 38
A customer has a centralized wireless deployment with N+1 high availability and few open authentication SSIDs configured. After failover, all APs are broadcasting all SSIDs, but the clients are assigned IP addresses from a different subnet. The WLANs on both WLCs are configured with the same dynamic interfaces. Which feature must be incorporated in the wireless design of the second controller?

NEW QUESTION 39
An engineer is designing coverage for a distribution warehouse with 12 m ceilings and metal racking that reaches 10 m. Which antenna design approach should be used?

NEW QUESTION 40
An engineer is designing a high-density WLAN that must support 100 concurrent users with 100 Mbps throughput consistently. The design allows for 20 Mbps per cell and per channel on the 5 GHz band. How many channels must the design use to provide 1 Mbps per user prior to RF overhead?

NEW QUESTION 41
An engineer must design AP placements for a new branch office that contains two floors. The engineer uses Ekahau to complete the predictive survey. To calculate the signal bleed through between floors, the engineer creates a building, adds the floors, and attenuation areas. After the scale is set, what else must be added on the floors to accurately measure the signal bleed at a specific location?

NEW QUESTION 42
An engineer must design and configure a wireless network for pervasive coverage in an oil terminal, casual web and email traffic, 5 GHz. What is the best design?