Free 300-615 Exam Braindumps certification guide Q&A [Q28-Q51]

Rate this post

Free 300-615 Exam Braindumps certification guide Q&A

300-615 Certification Overview Latest 300-615 PDF Dumps

Cisco 300-615 exam is a part of the CCNP Data Center certification program. Troubleshooting Cisco Data Center Infrastructure certification is designed to validate the skills and knowledge required to implement and troubleshoot modern data center technologies. Troubleshooting Cisco Data Center Infrastructure certification program covers a wide range of topics, including data center infrastructure, automation, virtualization, and more. The Cisco 300-615 exam specifically focuses on troubleshooting data center infrastructure issues.

Q28. Refer to the exhibit.

Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Q29. An engineer is troubleshooting an unexpected blade-server reboot. One of the DIMMs is displayed inside Cisco UCS Manager as “degraded with correctable errors” but is still available for the OS to use. Which action resolves the issue?

Reset the Cisco UCS chassis.

Replace the DIMM.

Reset the BMC.

Replace the CPU.

Q30. An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks.
Which statement about what occurs when the new uplinks are added is true?

Only new connections use the new uplinks automatically.

Paths must be defined before new connections can use the new uplinks.

All connections must be reset before the new uplinks can be used.

New and existing connections use the new uplinks automatically.

Q31. Refer to the exhibit.

The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

Q32. Refer to the exhibit.

The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

Enable IP redirects.

Set the MTU to 1500 bytes.

Configure HSRP version 2.

Configure the same HSRP group on both devices.

Q33. Refer to the exhibit.

A blade that is connected to FI-B fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA1 as the SAN Primary. Which set of actions resolves the issue?

* Set ESX01_B zone to VSAN 20.
* Create a new vHBA and assign VSAN 20.

* vHBA1 to VSAN 20 in Service Profile.
* VMware Adapter Policy on vHBA1.

*Apply VMware Adapter Policy on vHBA1
* Change vHBA1 to VSAN 20 in Service Profile

* Set ESX01_B zone to VSAN 20.
* Change vHBA1 to VSAN 20 in Service Profile

Q34. Refer to the exhibit. An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?

Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.

Set the local group number as 300 in the remote data center configuration

Run version 1 and version 2 HSRP on VLAN300 in the local data center.

Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.

Q35. An engineer performs a Cisco B-Series firmware upgrade using a host firmware pack and AutoInstall server feature on an adapter. The adapter activation stops at the pending-next-boot state. The issue occurs at the adapter activation stage during the BIOS and adapter update process. Which set of actions resolves the issue?

Revert the BIOS to the prior working version.
Reboot the operating system.

Log into Cisco UCS Manager.
Reset the adapter.

Disable the fabric services.
Reboot the server.

Set the Activate status on the adapter to Ready.
Reset the server.

Q36. Refer to the exhibit.

An engineer deploys SAN environment with two interconnected Cisco MDS 9000 Series switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit. Which action resolves the issue?

Import or export a zone set between the switches to synchronize the switches.

Change the name of one of the zones to match the other zone set.

Set the distribute policy of the zone to full.

Ensure that the zone members have different names.

Q37. Drag and Drop Question
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.

Q38. During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a “No Signal” message from the vKVM and physical connection. Which set of steps resolves the issue?

1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server

1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord

Q39. Refer to the Exhibit.

An Engineer cannot log in to the Cisco IMC page of the Cisco UCS C220 server. Which action resolve the issue?

Se the FQDN of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.

Use the DNS of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.

Replace the self-signed certificate that is installed on the Cisco IMC with a server certificate that is signed from the client corporate certificate.

Replace the self-signed certificate that is installed on the Cisco IMC with a user certificate that is signed from the client corporate certificate.

Q40. A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.

Q41. A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?

Set the same WWPN pools for vHBA adapters

Set the boot LUN to the highest LUN ID in the storage array

Set the boot LUN to the lowest LUN ID in the storage array

Set the same WWNN pools for vHBA adaptor

Q42. Refer to the exhibit. The job fails to run. Which action resolves the issue?

Configure an NTP server

Add a start time to the script

Renew the feature license

Enable the feature required

Q43. An IOM fails during a firmware upgrade and is unresponsive. Which action recovers the module?

Restore UCSM configuration from backup.

Roll back to the previous firmware.

Use AutoInstall to reinstall the firmware.

From the peer IOM, reset the faulty module.

Q44. Refer to the exhibit.

A network engineer finds one of the fabric interconnects offline when connecting L1 and L2 ports on both fabric interconnects. Which action resolves the issue?

1. Connect to Fabric Interconnect B.
2. Verify the cluster status and HA election.
3. Validate Fabric Interconnect B hardware issues.

1. Connect to Fabric Interconnect A.
2. Verify the cluster status and HA election.
3. Validate Fabric Interconnect A hardware issues.

1. Connect Fabric Interconnect B and change the role to primary.
2. Reboot Fabric Interconnect B.
3. Add the Fabric Interconnect A as subordinate fabric to the cluster.

1. Connect Fabric Interconnect B and execute “Erase configuration”
2. Reboot Fabric Interconnect B.
3. Add the subordinate Fabric Interconnect to the cluster.

Q45. Refer to the exhibit.

An engineer deploys SAN environment with two interconnected Cisco MDS 9000 Series switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit. Which action resolves the issue?

Import or export a zone set between the switches to synchronize the switches.

Change the name of one of the zones to match the other zone set.

Set the distribute policy of the zone to full.

Ensure that the zone members have different names.

Q46. The VXL AN fabric is deployed with this configuration:
*The VL AN 50 interface has no IP address on VTEP1 and VTEP4.
*The VLAN 100 interface has no IP address on VTEP2 and VTEP3.
* nve1 interface is configured on all VTEPs.
Host A experiences timeouts when attempting to ping host B. Which set of actions allows host A to reach host B7

On VTEP1, associate VNI 30000 to Test_ Telco VRF.
On VTEP4, associate VNI 20000 to Test_ Telco VRF.

On VTEP2, associate VNI 55000 to Test Telco VRF.
On VTEP4, associate VNI 50000 to Test Telco VRF.

On VTEP1, associate VNI 50000 to Test Telco VRFOn VTEP4, associate VNI 50000 to Test Telco VRF.

On VTEP2, associate VNI 30000 to Test Telco VRF
On VTEP4, associate VNI 20000 to Test Telco VRF

Q47. Refer to the exhibit. The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?

VSAN 1 is suspended.

The SFP is unsupported.

Trunk mode must be activated.

The interface is in an incorrect mode.

Q48. Refer to the exhibit.

A switch is being downgraded to an earlier release because of a problem with the current release. After the switch is downgraded, it can no longer forward traffic. Which action resolves the issue?

Enable ISSD after the downgrade is complete.

Roll back to the original image.

Reload the switch.

Shut and no shut the interfaces to the FEX.

Q49. Refer to the exhibit.

An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?

Configure the role name to match the group name on Microsoft Active Directory.

Include specific users into MDS role configuration.

Configure SSH logins on Cisco MDS switch.

Integrate Cisco MDS with Microsoft Active Directory.

Q50.

Refer to the exhibit. A network engineer deploys scripts to the guest shell of a Cisco Nexus switch. The scripts fail to operate properly due to the limited CPU and file system resources that are assigned by default to the guest shell. The engineer allocated more memory and disk space to the guest shell, but the application continues to fail. Which action resolves the issue?

Disable and enable bash shell

Reboot the guest shell

Redeploy the bash shell

Upgrade the guest shell

Q51. Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.

Reconfigure the Drive Type from “Removable” to “Non-Removable”

Insert an SD card into SLOT-2

Configure the RAID that is associated with the card.

Set SLOT-1 Sync Mode to “Auto”

Cisco 300-615 exam has been specifically designed to help professionals develop a deep understanding of data center infrastructure and its associated technologies. 300-615 exam is ideal for network administrators, system engineers, and technical support personnel who are responsible for ensuring the smooth functioning of data center infrastructure. By taking 300-615 exam, professionals can demonstrate their ability to troubleshoot complex data center issues and provide effective solutions to improve the overall performance of data center operations. Successful completion of the 300-615 exam can help professionals advance their careers and open up new opportunities in the field of data center technology.

The Best Cisco 300-615 Study Guides and Dumps of 2024: https://www.trainingquiz.com/300-615-practice-quiz.html

Quiz Training Materials

Free 300-615 Exam Braindumps certification guide Q&A [Q28-Q51]

Latest 500-445 Study Guides 2022 – With Test Engine PDF [Q33-Q55]

Verified 500-430 Exam Dumps PDF [2024] Access using TrainingQuiz [Q28-Q49]

Leave a Reply Cancel reply

Quiz Training Materials

Free 300-615 Exam Braindumps certification guide Q&A [Q28-Q51]

You May Also Like...

Latest 500-445 Study Guides 2022 – With Test Engine PDF [Q33-Q55]

Verified 500-430 Exam Dumps PDF [2024] Access using TrainingQuiz [Q28-Q49]

Leave a Reply Cancel reply