Grab latest CWNP CWDP-305 Dumps as PDF Updated on 2026 [Q151-Q172]

Q151. You are creating an outdoor bridge link that spans more than 1000 yards. Which one of the following antenna types is more likely to be included in the design?

Q152. What is the purpose of Friis transmission equation [ (LdB) = 20 log(d) + 20 log (f) – 27.55 ]?

Q153. Using a SCA means that all APs will be using the same channel in a given layer. How is the AP with which the client associates determined?

Q154. Which advantage provided by 802.11n and 802.11ac is not usable in 1×1:1 low-end client devices?

Q155. How much more power can a 1 Mbps 802.11b signal have than a 54 Mbps 802.11g signal if it is sent through a saturated amplifier?
Response:

Q156. When performing a spectrum analysis walkthrough of a facility tor which you will be creating a WLAN design you detect an interferer What should you do?

Q157. What is the most cost-effective way to accurately measure the height of a ceiling when the use of a ladder is not permitted?

Q158. What service must be implemented on your customer’s network to authenticate users against an LDAP database before granting access to the WLAN infrastructure?

Q159. What is a radome?

Q160. What is a radome?

Q161. When using a WLAN design tool with propagation modeling capabilities, what critical step must be performed before adding APs, antennas, and attenuation factors like walls?

Q162. An associated STA detects a new BSS with the same SSID as the STA’s current BSS. The new BSS uses a different IP subnet than the current BSS. If the STA is configured to use 802.1X/EAP preauthentication, what is likely to occur?

Q163. Which DHCP option, when required, should be configured and enabled to help APs locate their wireless LAN controller?

Q164. Before performing a pre-deployment passive RF survey of a new deployment using survey mapping software, which of the following must be performed?
Response:

Q165. Given:A WLAN controller is connected to ABC Company’s core Layer 3 Ethernet switch with an IEEE 802.1 Q trunk connection. The WLAN controller’s native VLAN is VLAN 6 and its IP address is 10.0.14.2 /24.
Lightweight APs supporting centralized forwarding are connected to the network on VLANs 7, 8, and 9, and they each build a Layer 3 tunnel back to the WLAN controller’s IP address.
The dynamically assigned IP addresses received by each AP from a DHCP server will be ________________.

Q166. You ate evaluating CO impact in 2 4 GHz. During the post-validation survey, you determine that 2 or 3 APs are seen from every location in the 2 4 GHz band with signal strengths above -75 dBm from all seen Aps.
Does this show that CO has been removed from the environment given that three non-overlapping channels exist in 2.4 GHz and why?

Q167. Given: The 802.11ac APs you have selected for your public access deployment support many of the PHY and MAC enhancements offered by the 802.11n and 802.11ac amendments. The AP is configured for a single- band (2.4 GHz) and only allows 20 MHz channels. The WLAN radio in the AP is a 3×3 802.11n chip that supports two spatial streams. What is the maximum MCS rate that could be supported by this AP?

Q168. After deploying a 5 GHz-only WLAN infrastructure in the USA, using 20 MHz channel-widths and all 25 available channels, one of the managers of the company brings his 802.11n tablet to the office to test the Guest SSID. While testing, there were several spots where we would get poor RSSI (below -80dBM) or none at all. You checked the WLAN infrastructure and all APs are up and running and you’ve validated coverage after deployment. What is causing this issue?

Q169. Main Topic:Post-Design ValidationandTroubleshooting
Question:
One of your warehouse customers called you reporting problems with their WLAN in some locations that you designed and installed over a year ago. What should be one of your first considerations for your line of questioning?

Q170. What are some advantages of designing guest access with all guest users tunneled directly into the DMZ?
Response:

Q171. What should you do during the design process of a point-to-point bridge link to minimize CCI and ACI?

Q172. You have been asked to design a WLAN for an organization. They will be replacing an existing WLAN.
Currently each AP operates 8 SSIDs on each radio. What will you communicate with the organization so that they understand the need to reduce the number of SSIDs?